 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MUR1620CT GLASS PASSIVATED HIGH EFFICENCY RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 16.0 Amperes Features * Low forward voltage, High current capability * Plastic package has Underwriters Laboratory Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound. * High surge capacity * Low power loss, high efficiency * Ultra fast recovery times, high voltage Mechanical Data * Case: Molded plastic, TO-220 * Terminals: leads solderable per * MIL-STD-202, method 208 guaranteed * Polarity: As marked * Mounting Position: Any PIN 1 PIN 2 CASE PIN2 Positlve CT Absolute Maximum Ratings and Characteristics Dimensions in mm Ratings at 25 ambient temperature unless otherwise specified. Single phase, half wave,60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward Rectified current at TC = 100 Peak forward surge current 8.3ms single half-sine-wave superimposed on rated load (JEDEC method) Maximum forward voltage at 8.0A and TA = 25 Typical junction Capacitance (Note1) Maximum reverse recovery time (Note 2) Typical thermal resistance (Note3) Maximum reverse current at rated DC blocking voltage @TA = 25 @TC =125 IF(AV) IFSM VF CJ TRR R0JC IR TJ ,Ts 16.0 125 1.0 80 50 3.0 10 500 -55 to +150 Amps Amps Volts pF nS /W Amps Amps VRRM VRMS VDC Value 200 140 200 Units Volts Volts Volts Operating and storage temperature range Notes :1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC. 2. Reverse recovery test conditions: IF = 0.5A, IR = 1A, IRR = 0.25A 3. Thermal resistance from junction to case per leg mounted on heatsink. SEMTECH ELECTRONICS LTD. (R) (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/06/2003 MUR1620CT FIG.1 Reverse Recovery Time Characteristic and Test Circuit Diagram 50 NONINDUCTIVE 10 NONINDUCTIVE +0.5A DUT (+) 50Vdc (appox) (-) 1 NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (-) PULSE GENERATOR (NOTE 2) (+) -1.0A 1cm SET TIME BASE FOR 5/10ns/cm 0 -0.25A trr NOTES:1. Rise Time=7ns max. Input Impedance= 1 megohm 22 pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms Average Forward Current. (A) Instantaneous Reverse Current. ( A) 20 16 12 8 4 0 0 FIG.2 Muximum Forward Current Derating Curve 1000 FIG.3 Typical Reverse Characteristics Per Leg 100 Tj=125C 10 Tj=25C 50 100 150 Case Temperature. (C) FIG.4 Maximum Non-repetitive Forward Surge Current Per Leg 1 Peak Forward Surge Current. (A) 0.1 120 90 60 30 Tj=25C 8.3ms Single Half Sine Wave JEDEC Method 20 40 60 80 100 120 140 Percent of Rated Peak Reverse Voltage. (%) FIG.6 Typical Forward Characteristics Per Leg Number of Cycles at 60Hz FIG.5 Typical Junction Capacitance Per Leg Capacitance. (pF) 240 200 160 120 80 40 0 1 2 5 10 20 50 100 200 500 1000 Tj=25C Instantaneous Forward Current. (A) 1 2 5 10 20 50 100 100 30 10 3.0 1.0 0.3 0.1 0.03 Reverse Voltage. (V) 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 Tj=25C PULSE WIDTH-300 s 1% DUTY CYCLE Forward Voltage. (V) SEMTECH ELECTRONICS LTD. (R) (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/06/2003 |
Price & Availability of MUR1620CT
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |